Funbie Studios

Alrighty, with a bit more detailing in place, and also a new addition - we're ready for test printing to finalize this kit! 😉

Been having fun with Micronus Prime's unicycle mode but kinda didn't like that it couldn't balance without the exhaust pipes rotated downwards to form kickstands. So, we're messing with some ideas to address that 💡

All together now with Steve and Bumblebee!

Let's welcome A-A-Tron, another pal of Bumblebee's from sub level-50! Though he only has his upper torso, both of A-A-Tron's arm can be rotated up and down, and his left hand also comes with elbow articulation.

#3dprint files now up at www.patreon.com/posts/141886877!

Think the broad look for A-A-Tron is locked in, so here's having some fun adding all his details in! 😁

A friend of Steve's is in the works ... 😁

Here's the next display stand for Oynx Prime! Comes with a separatable logo so it can be either opaque or translucent, a back piece to hold Oynx Prime primemaster and the base which doubles as parts storage.

#3dprint files now up at www.patreon.com/posts/141618644!

Up next - it's Oynx Prime's turn to get his display stand! 😉

We've opted to use a clear 4mm acrylic pipe filled with UV resin, half filling twice to suspend the spark within, before finishing it up with a clear blue spray for the exterior of the body.

Here's a tiny package which contains enough sparks from fallen friends, and hopes for a new ally's rebirth - all housed safely in this spark canister!

#3dprint files now up at www.patreon.com/posts/141437437!

Yeah, it's gonna be the spark canister from Skybound - holding the very essence of a bot within. Coming soon! 😊

Working on a smaller piece from the Skybound comics next ... 😉

And to give it a little CyberTrack and also WFC tracks compatibility, the rear door comes with a notch where a connector piece can be printed and emplaced, letting you connect up to more tracks or with other baseformers!

The back doors open up revealing the interior details and there's where your bot troops can be loaded up before jetting off! And also, here it is alongside core / legend class figures which can fit in within!

Right out of the pages of the beloved Skybound comics - here's the Autobot troops transport pod which was attached underneath Jetfire!

#3dprint files now up at www.patreon.com/posts/141262655!

Got most of the details we wanted in - time to crank it all out for assembly! 😀

With the important scaling in place - it's time to go full speed with fleshing out the core details! Oh and yes - it's going to be the troop transport pod which Jetfire uses in the Skybound comics! 😁

Embarking on something ambitious ... this might take a while 😅

For the other modes he has, the bow and arrow mode might look a little strange with the arrow extended a little more forward. But there's always the option of taking the piece out in that case.

Whilst fun in all his different modes, one thing which bugged us was Oynx Prime's short staff. Time for a quick extender piece to fix that!

#3dprint files now up for free at www.patreon.com/posts/140804307!

Kind of weird that Oynx Prime's staff isn't long enough to reach the floor when it's being held - so it's time for a quick extender piece to address that!

Thank you! We have merchant partners whom you can reach out to if you'll like to get physical printed kits:

www.facebook.com/profile.php?... - or - Printing.3ds@outlook.com

www.facebook.com/collectorcrafts/ -or- collectorcrafts01@gmail.com

Here's the blaster being used by WFC Siege Magnus also, just to see how it fits too!

To complete Magnus' setup as he leads the Autobots into combat, here's his blaster from the Skybound comics, complete with a 5mm sized barrel port for blast effects!

#3dprint files now up at www.patreon.com/posts/140485881!

Had some fun putting all the details on this blaster - so it's time to bring it to life next... 😉

Roughing out Ultra Magnus' blaster from Skybound! 😁

We've again included a Primemaster slot version, where the Alpha Trion primemaster to be used in lieu of the front facing logo.

And finally, the base of the display stand lifts up to allow for storage of accessories and parts for safekeeping.

Here's the latest display stand for Alpha Trion, featuring a logo which can be printed in transparent (to light up) or opaque material separately and swapped about as you like!

#3dprint files now up at www.patreon.com/posts/140189308!

Decided to take the same separated parts approach for Alpha Trion's logo on his display stand - to make for easier single colors printing, and also be easily swapped between opaque and solid colors.

Coming soon! 😁

Too true! 🤣